Film Development Times: Charts, Temperature Compensation and Dilutions
A development time is only meaningful with four other numbers attached: the film, the developer, its dilution and the temperature, plus the speed you rated the film at and how you agitate. Change any one and the time changes. This guide explains how to read a development chart, gives manufacturer starting times for the most popular black and white films, and shows how to correct for temperature.
What a development time depends on
- Film. Each emulsion develops at its own rate. Tabular-grain films such as T-Max and Delta often need different times from traditional films of the same speed.
- Developer and dilution. Diluting a developer 1+1 typically lengthens the time by roughly a third to two thirds, depending on the film. See film developers explained.
- Temperature. The standard is 20°C (68°F). Warmer developer works faster.
- Exposure index. Rating a film above box speed and pushing it needs more time. See push and pull processing.
- Agitation. More frequent agitation develops faster and with more contrast. Continuous rotary processing usually needs about 10 to 15 percent less time than inversion in a small tank.
Starting times for popular black and white films
These are the manufacturers' published times for small-tank (spiral reel) development at 20°C (68°F) with intermittent agitation, with the film rated at box speed. Treat them as a starting point: your thermometer, water, agitation and taste all move the result.
| Film | Developer | Dilution | Time at 20°C |
|---|---|---|---|
| Kodak Tri-X 400 | D-76 | Stock | 6¾ min |
| D-76 | 1+1 | 9¾ min | |
| XTOL | Stock | 7 min | |
| XTOL | 1+1 | 9 min | |
| HC-110 | Dilution B | 3¾ min | |
| Ilford HP5 Plus | Ilfotec DD-X | 1+4 | 9 min |
| ID-11 | Stock | 7½ min | |
| ID-11 | 1+1 | 13 min | |
| Ilfosol 3 | 1+9 | 6½ min | |
| Rodinal | 1+25 | 6 min | |
| Rodinal | 1+50 | 11 min | |
| Ilford FP4 Plus | Ilfotec DD-X | 1+4 | 10 min |
| ID-11 | Stock | 8½ min | |
| ID-11 | 1+1 | 11 min | |
| Rodinal | 1+25 | 9 min | |
| HC-110 | Dilution B | 9 min |
Sources: Kodak publication F-4017 for Tri-X 400, and Ilford's HP5 Plus and FP4 Plus technical data sheets. Manufacturers revise these sheets, and Ilford's times for Kodak developers sometimes differ from Kodak's own, so check the current sheet for your film before an important roll.
Times under five minutes
Some combinations come out very short, such as Tri-X in HC-110 Dilution B at 3¾ minutes. Kodak and Ilford both warn that times under about five minutes in a small tank can give uneven development, because the first fill and the final pour take a noticeable share of the total. Use a more dilute developer instead. HC-110 is often used at 1+63, sometimes called Dilution H, at roughly double the Dilution B time, which brings Tri-X to a comfortable seven or eight minutes.
Temperature compensation
If your developer isn't at 20°C, adjust the time rather than waiting for the water to change. Development speeds up by very roughly 8 to 10 percent for each 1°C (about 2°F) warmer. Ilford's own example, from its data sheets: a time of 4 minutes at 20°C becomes 3 minutes at 23°C and 6 minutes at 16°C. Ilford and Kodak both publish temperature compensation charts that plot this curve for any starting time.
| Temperature | Approximate time, if 10 min at 20°C |
|---|---|
| 18°C (64°F) | 12 min |
| 20°C (68°F) | 10 min |
| 21°C (70°F) | 9 min |
| 22°C (72°F) | 8¼ min |
| 24°C (75°F) | 7 min |
These figures follow the shape of the manufacturers' curves and are close enough for black and white film. Stay between about 18°C and 24°C: colder developers work unpredictably, and warmer ones give times too short to control and soften the emulsion. Color processes are different: C-41 runs at 37.8°C (100°F) within a few tenths of a degree, and E-6 is stricter still.
Push and pull times
Data sheets usually list times for higher exposure indexes. Ilford gives HP5 Plus in DD-X 1+4 as 9 minutes at EI 400, 10 at EI 800, 13 at EI 1600 and 20 at EI 3200. Where a sheet gives no push time, a common starting point is about 30 to 50 percent more development for each stop, though the right figure varies widely between films and developers.
Where to find development times
- The film's technical data sheet, from Kodak, Ilford, Foma or the maker of your film. This is the most authoritative source.
- The developer's data sheet, which often lists other makers' films.
- The Massive Development Chart, published by Digital Truth, collects thousands of film and developer combinations submitted by manufacturers and photographers. It is the most comprehensive chart available, but some entries are user-submitted, so confirm unusual times against the data sheet.
- Your own notes. Once a time works for you, write it down with the temperature and agitation. That becomes the most reliable chart you own.
Agitation
Development times assume a particular agitation pattern. Ilford's standard is four inversions in the first 10 seconds of each minute; Kodak's small-tank method is five to seven inversions every 30 seconds. Pick one, use it every time, and adjust the time to suit, rather than changing both at once. Stand development uses almost no agitation and very long times in dilute developer.
Dialing in your own time
If your negatives are consistently too contrasty, with blocked highlights, shorten development by 10 to 15 percent. If they are flat, with highlights that print gray, lengthen it by the same amount. Thin shadows mean underexposure, which development can't fix; see common film problems. The Zone System takes this idea further, matching development to each scene's contrast.
Terms in this guide
More on developing film
All the guides are on the Learn Film Photography page, and every term is in the glossary. Shot something on film? Share it in the gallery.