FilmPhotography.com Real light. Real film.

Color Darkroom Printing: RA-4 and Chromogenic Prints

You can print color negatives in a darkroom much as you print black and white, using an enlarger, color paper and the RA-4 process. The result is a chromogenic print, or C-print, the same kind of print a photo lab makes, but with every color decision in your hands. It needs total darkness, a way to filter the enlarger's light and some patience with color balance, and it is far more achievable at home than most people expect.

What a chromogenic print is

A chromogenic print is made on paper with three emulsion layers, sensitive to blue, green and red light. During development, dye couplers in each layer form yellow, magenta and cyan dyes where silver has been developed; the silver is then bleached away, leaving a dye image. The name comes from this color-forming step. Almost every color photograph printed from film or digitally on photographic paper in the last half-century is a chromogenic print, including digital prints that labs make by exposing color paper with lasers or LEDs, often sold as "C-prints" or "Lambda prints."

What you need

The RA-4 process

The standard RA-4 process runs at 35°C (95°F) with a 45-second development and a 45-second blix, followed by a wash. Home kits are often designed to run at lower temperatures, even room temperature, with longer times. Follow the kit's instructions: like C-41, RA-4 depends on consistent time and temperature, and a change in either shifts color and density.

StepPurpose
DeveloperDevelops silver and forms the dye image
Stop or rinse (optional)Ends development quickly and protects the blix
Bleach-fix (blix)Removes silver and unexposed halide, leaving dyes
WashRemoves chemicals; a few minutes is enough for RC paper
DryColor papers are resin coated and dry flat

How color filtration works

To correct a color cast in the print, you change the color of the enlarger light with yellow and magenta filtration. Cyan is usually left at zero. The rule takes a moment to absorb because it works in reverse:

To remove a cast from the print, add that color to the filtration. If a print is too yellow, add yellow; too magenta, add magenta. If it is too blue, remove yellow; too green, remove magenta. Red needs both yellow and magenta added; cyan needs both removed.

Adding filtration also lengthens the exposure slightly, so changes of more than about 10 units usually need a small exposure increase.

Finding the right balance

  1. Start from a typical filtration from the paper's data sheet or from notes for your enlarger. Every combination of enlarger, lamp, paper and film differs, so expect to adjust.
  2. Make a test strip for density at that filtration, as you would in black and white, judging midtones and skin.
  3. Judge the color on a dry print under daylight-balanced light. Wet prints look different.
  4. Adjust filtration in steps: 5 to 10 units for a slight cast, 20 or more for a strong one.
  5. Use a ring-around, a chart of the same print with deliberate casts, to identify which color is wrong. Casts are easiest to judge in neutral grays and skin tones.

Once you have a good filtration for one negative, other negatives on the same film shot in similar light will be close. Write it down with the exposure.

Color negatives, slides and other prints

RA-4 paper is made for printing from color negatives, whose orange mask the paper is designed around. Printing slides directly to a positive print used to be done on reversal papers such as Cibachrome (later Ilfochrome), which are no longer made. Today, slides are usually printed by scanning them, or by making an internegative. You can also print black and white negatives on color paper for a neutral or toned look, though black and white paper gives better tones.

Dodging and burning in color

Dodging and burning work as in black and white; see dodging and burning. You can also locally adjust color by dodging or burning through a colored filter, for example warming a cold sky. Do this lightly: a local cast that doesn't match the rest of the print looks wrong very quickly.

Is RA-4 at home worth it?

If you scan your negatives, a lab's digital print on the same paper is easier and very good. Darkroom color prints offer something else: an optical print with no scan in between, colors you set by eye, and the satisfaction of a craft few people still practice. A community darkroom with a color processor is a good way to try it without equipment of your own; the darkroom rental section of our directory lists some.

Terms in this guide

More on the darkroom

All the guides are on the Learn Film Photography page, and every term is in the glossary. Shot something on film? Share it in the gallery.