F-Stop Printing: Timing Darkroom Exposures in Stops
F-stop printing is a way of timing darkroom exposures in stops instead of seconds. Rather than adding two or five seconds to a print, you add a third or half of a stop, the same way you think about exposure in the camera. It makes test strips more even, dodging and burning more predictable, and changes in print size or paper easy to work out. Popularized by Gene Nocon in the 1990s, it is now the method most experienced printers use.
The problem with seconds
A traditional test strip adds the same number of seconds to each step: 5, 10, 15, 20, 25 seconds. But the eye and the paper respond to ratios, not differences. Going from 5 to 10 seconds doubles the exposure, a full stop; going from 20 to 25 adds only a third of a stop. So the steps at the start of a linear strip are huge and the steps at the end are tiny, and the one you need is usually between two of them.
The same thing happens with burning. "Burn the sky for 5 seconds" means a lot on a 10-second print and very little on a 40-second one. In stops, "burn the sky one stop" means the same thing whatever the base time.
How f-stop timing works
Each stop doubles the exposure. A fraction of a stop multiplies the time by a fixed factor:
| Change | Multiply time by | From 12 seconds |
|---|---|---|
| +1/3 stop | 1.26 | 15.1 s |
| +1/2 stop | 1.41 | 17.0 s |
| +2/3 stop | 1.59 | 19.0 s |
| +1 stop | 2 | 24 s |
| −1/3 stop | 0.79 | 9.5 s |
| −1/2 stop | 0.71 | 8.5 s |
Many printers work in sixths or twelfths of a stop for fine adjustments: a twelfth of a stop is about a 6 percent change, near the smallest difference you can see in a print.
An f-stop test strip
Instead of equal seconds, each band of the strip gets a third of a stop more than the one before. Starting from 8 seconds, the bands receive:
| Band | Total exposure | Extra time for this band |
|---|---|---|
| 1 | 8.0 s | 8.0 s (whole strip) |
| 2 | 10.1 s | +2.1 s |
| 3 | 12.7 s | +2.6 s |
| 4 | 16.0 s | +3.3 s |
| 5 | 20.2 s | +4.2 s |
| 6 | 25.4 s | +5.2 s |
| 7 | 32.0 s | +6.6 s |
Expose the whole strip for the first time, then cover one more band before each additional exposure, as in a normal test strip. Every step now looks evenly spaced, and the strip covers two full stops. Use half-stop steps for a rough first strip and third- or sixth-stop steps once you're close.
Several short exposures don't always add up exactly to one long one, because the enlarger lamp takes a moment to reach full brightness and to fade each time. For most enlargers the difference is small; for precision, make each band a separate exposure from zero rather than an increment.
Dodging and burning in stops
F-stop thinking makes dodging and burning notes portable. If a base exposure is 16 seconds and the sky needs one more stop, burn for 16 seconds. If you later make the print larger and the base exposure becomes 24 seconds, the sky still needs one stop, now 24 seconds. Dodging works the same way: holding back a face by half a stop on a 16-second base means dodging for about 4.7 seconds, the difference between 16 and 11.3 seconds.
Write your print map in stops ("base 2.0 stops above 8 s, burn sky +1, dodge doorway −1/3") and it will survive changes in paper, enlargement and enlarger.
Split-grade printing in stops
Split-grade printing pairs naturally with f-stop timing. Make one test strip with the grade 00 filter for the highlights and one with grade 5 for the shadows, both in third-stop steps, then add the two exposures together. Changing contrast then means shifting stops between the soft and hard exposures.
Timers and tables
You can do f-stop printing with any timer and a printed table of times, or by calculating 2n on a phone before you turn the lights off. Dedicated f-stop enlarger timers make it easier: you set a base time and step in stops, and the timer works out the seconds for you. Some photographers also use free phone apps with a dark red screen, though the screen must be dim and shielded from the paper.
Changing print size
When you raise the enlarger head, the light spreads over a larger area and the exposure has to increase. The required change follows the square of the magnification: going from an 8x10 to an 11x14 print of the same negative, the linear magnification rises by about 1.4 times, which needs about one stop more. Thinking in stops makes the adjustment a single number. Make a quick test strip to confirm, since lens and enlarger behavior vary.
Terms in this guide
More on the darkroom
All the guides are on the Learn Film Photography page, and every term is in the glossary. Shot something on film? Share it in the gallery.