Printing on Fiber Paper: Developing, Archival Washing, Drying and Flattening
Fiber-based paper is the traditional black and white printing paper, and many photographers consider it the finest. Prints have deeper blacks, a surface that looks like part of the image rather than a coating on it, and the potential to last for centuries. It also takes longer to process, wash and dry than resin-coated paper, and it curls. This guide covers what's different about working with fiber, step by step.
Fiber vs RC paper
Resin-coated (RC) paper seals the paper base between layers of polyethylene, so chemicals can't soak into it. It develops fast, washes in a couple of minutes and dries flat. Fiber-based paper has an uncoated paper base under a layer of baryta (barium sulfate) and the emulsion. Chemicals soak right through, which is why every step takes longer.
| RC paper | Fiber paper | |
|---|---|---|
| Development | About 1 minute | 2 to 3 minutes |
| Washing | 2 to 5 minutes | Much longer; see below |
| Drying | Flat, in minutes | Curls; needs screens or a press |
| Dry-down | Slight | Noticeable: prints darken as they dry |
| Toning and archival life | Good | Excellent |
Learn on RC, where mistakes are cheap and quick to see, then move to fiber for prints you want to keep. See darkroom printing basics.
Exposing fiber paper
The fiber and RC versions of a paper often differ in speed and contrast, so a time worked out on RC is only a starting point. Make your test strips on the same fiber paper you will print on, and judge them dry, or allow for dry-down: fiber prints look lighter wet than they will dry, often by around 5 to 10 percent in exposure. Many printers make a final print slightly lighter than looks right in the tray, or microwave a test strip dry before judging it. F-stop timing makes this easy: shorten the exposure by a twelfth or a sixth of a stop.
Developing
Develop fiber prints for two to three minutes, or as long as the paper's data sheet suggests, with continuous gentle rocking. Full development gives the richest blacks; pulling a print early leaves muddy shadows. Slide prints into the developer face down then turn them over, so the whole surface wets at once.
Stop and fix
Use a stop bath for 10 to 30 seconds. For fixing, fiber prints need care: too little and the print will stain over time, but too much lets fixer soak deep into the paper fibers, where it is hard to wash out. Two common approaches:
- Two-bath fixing. Fix for half the time in a first bath and half in a second, fresher bath. The first bath does most of the work and is discarded first; the second stays nearly fresh. This is the classic archival method.
- Short fixing in rapid fixer. Fix for about a minute in a film-strength ammonium thiosulfate fixer. Ilford's archival sequence for fiber paper uses this, which keeps fixer from soaking deep into the base and greatly shortens the wash.
Washing aid and washing
A washing aid, also called hypo clearing agent, converts residual fixer into compounds that wash out far faster. Rinse briefly after the fixer, soak the print in washing aid for the time on the bottle, then wash.
- With a washing aid: wash for around 20 to 30 minutes in running water, depending on paper weight. Ilford's short-fix sequence needs less: a 5-minute wash, 10 minutes in washing aid, and a final 5-minute wash.
- Without a washing aid: an hour or more.
Wash prints so water can reach both sides, ideally in a vertical slot washer that keeps them separate. Prints stacked in a tray stick together and wash unevenly; if you use a tray, shuffle them constantly. Wash water should be close to the temperature of the other solutions.
Toning
Fiber prints respond beautifully to toning. Selenium toner, diluted, deepens blacks slightly and protects the silver image against pollution; stronger dilutions shift tones toward purple-brown. Sepia toner gives warm browns. Tone after fixing and before the final wash. Selenium is toxic: use gloves and ventilation.
Drying fiber prints
Fiber prints curl as they dry because the paper base shrinks more than the emulsion. Options:
- Drying screens: squeegee the print gently and lay it face down on clean fiberglass window-screen frames. It dries with a gentle curl, which is flattened later.
- Hanging: clip prints back to back in pairs; they curl but dry quickly.
- Gummed tape on glass: the traditional method for a flat print, though the taped edges are trimmed off.
Flattening
The usual way to flatten dried fiber prints is a dry mount press: put the print between two sheets of clean mat board or release paper and press it warm for a minute or two, then let it cool under a weight. Without a press, dampen the back of the print lightly and leave it between blotters under heavy books overnight.
Glossy and matte surfaces
Fiber glossy paper air-dries to a soft semi-gloss, not the mirror gloss of glossy RC. The high gloss seen in old prints came from ferrotyping, drying the print face down against a polished metal or glass plate. Matte and semi-matte fiber surfaces dry much as they look wet.
Keeping it practical
Fiber printing rewards patience but consumes it. Work out the print on RC or with fiber test strips, make the final prints in one session, and leave washing and drying to run while you clean up. Keep notes on exposure, filter grade, development and toning for each print; see dodging and burning for print maps.
Terms in this guide
More on the darkroom
All the guides are on the Learn Film Photography page, and every term is in the glossary. Shot something on film? Share it in the gallery.